Professional Reliable Industrial Stainless Steel Pulse Dust Collector Manufacturer

Product DescriptionProfessional Reliable Industrial Stainless Steel Pulse Dust Collector ManufacturerProduct Introduction   Tianfeng TLCM series pulse filter-bucket dust collector is a new kind dust collecting device. The dust collector has many characteristics such as high purification efficiency, small size, large filtering area, good filtering effect, low pressure loss, long service life of the filter cylinder, quick and convenient installation and maintenance, continuous use and so on.Technical Characteristics1. The dust collector has many advantages such as high dust removal efficiency, good filtering effect, small size and stable operation.2. The filtering cylinder adopts skeleton installation, good sealing property, firm and reliable.3. The filtering cylinder has long service life, and it is convenient to install and maintain.4. The box adopts air-tight design, and the sealing property is good. The inspection door of the dust collector adopts excellent sealing material, and the air leakage rate is low.5. The layout of the inlet and the outlet of the air duct are compact, and the resistance of airflow is low.Structure And Working PrincipleTianfeng TLCM series pulse filter-bucket type dust collector is equipped with air inlet, filtering cylinder, air outlet, air bag, pulse controller, injecting and blowing valve, injecting and blowing pipe, etc. The filtering cylinder is made of folded and rolled polyester fiber, and the lower end of the the filtering cylinder is closed. The upper center directly faces the lower mouth of the injecting and blowing pipe. After the air with dust enter into dust remover through air inlet, the speed of the air flow will slow down. The coarse particles can separate from air flow and settle on the internal part of dust collector, and the fine powder will be filtered continuously and be prevented outside of the filtering cylinder, and the purified clean air will be discharged from air outlet. When the ash layer on the filtering cylinder surface is thicker, the pulse controller will give an order, and the injection and blowing valve will start to work. At that time, the compressed air in air bag will inject and blow out through injecting and blowing pipe in a higher speed. At the same time, it can induce more fresh and clean air to enter into filtering cylinder, and make the air quickly flow from inside to outside and blow the ash on the outside surface of the filtering cylinder. At last, the collected dust will be discharged from discharging ash hopper. The dust removing method of Tianfeng TLCM series pulse filter bucket type dust collector adopts the method of pulse type injecting and blowing. It not only can clean dust thoroughly, but also can not harm filtering cylinder. It can effectively ensure the service life of the filtering cylinder. The procedure of dust cleaning is automatically controlled by pulse controller, and it can adopt pressure difference control or time control.Applicable IndustriesTianfeng TLCM series pulse filter barrel type dust collector is wide applicable to the purification of air with dust and the recycling of dust materials in many industries such as food, pharmacy, feeds, metallurgical, building materials, cement, machinery, chemical, electricity and light industry.Technical ParametersSpecificationFiltering areaNumber of filterSpeed of filtering (m/min)Filtered air volume (m3/h)Maximum overall dimension (mm)Consumption of compressed air ( m²)TLCM-018.2510.8-1.2400-600600x700x17000.02-0.10TLCM-0216.520.8-1.2800-1200700x900x18000.04-0.17TLCM-0424.7540.8-1.21600-24001100x1200x20000.07-0.30TLCM-0649.560.8-1.22400-36001100x1700x22000.11-0.30TLCM-086680.8-1.23200-48001200x1400x27000.11-0.30TLCM-1299120.8-1.24800-72001200x1800x28000.13-0.40TLCM-16132160.8-1.26400-96001900x40000.15-0.50TLCM-24198240.8-1.29600-144002200x45000.18-0.60TLCM-36297360.8-1.214400-216003000x56000.20-0.60TLCM-48396480.8-1.219200-288003500x58000.20-0.60Processing Procedure     Packaging & ShippingAfter you place the order and pay the deposit in our company, we will start to arrange the production and contact the ocean freight transportation agency to reserve the position. Two days before the end of production, you need to complete the final payment. Then, we will inform the ocean cargo transportation agent company that it is ready to come to the factory to pull the goods to the port. On the day of delivery, we will send you the factory video and pictures, and mark the corresponding English name of each product and product parts with a marker to prevent you from not knowing what each part is after receiving the goods. At the same time, we will put the English version of the product instructions in the cargo box. We generally select freight forwarders with preferential prices for customers to deliver goods for you. The shipping method can be FOB or CIF. You can also choose EXW, and then contact the goods agent company yourself. About the packaging method and the shipping method, if yo