Modified PVC Ultrafiltrate Membrane Filter 250series

Product DescriptionPVC series pressurized UF membrane modules use imported PVC raw material with long service life,filtering precision is 0.01 micron. Due to its high rigidity, PVC can be made to thicker hollow fibers and bearhigh working pressure, which is applicable to inside-out working mode. it has good water permeability, mechanical properties, chemical resistance and anti-pollution ability, and the cut molecular weight is 100,000 Dalton.Inside-out structure is applicable forraw water with low turbidity and SS. When inside-out membrane modules work, contaminants are rejectedinside hollow fibers without dead angles, which are easy to be washed out.IGFUFC250 membrane module is installed with hollow membrane filament with inner diameter of 1mm and outer diameter of 1.8mm, and the filtration method is internal pressure type, i.e. the raw water enters into the inner part of the hollow filament first, and then is driven by the pressure difference, and then permeates through the filament along the radial direction from the inner to the outer part, which can filter out all kinds of bacteria, colloids, suspended matter, microorganisms and other harmful substances in raw water.It can filter out all kinds of bacteria, colloid, suspended solids and microorganisms and other harmful substances in the raw water. Product Parameters IGFUFC250 technical detailsModel IGFUFC250StructureInternal pressure typeMembrane materialModified PVCCut molecular weight100000 DaltonNominal membrane area48m2Filament diameter  ID1.0mm,OD 1.8mm Out sizeφ250mm×1710mmConnection sizeDN50 coupling; Pure water flux12000L/H(0.15MPa, 25ºC)  Product Features★ High filtering precision: can reach 0.01μm★ High pure water flux: 35-100L/m.h★ High porosity: >95%★ High strength:>600CN★ Long service life: 3~5 years service life under normal use★ Low breaking rate of hollow fibers: to ensures stable qualityof ultrafitrate Application★ Treatment of surface water & ground water ★ Municipal drinking water treatment ★ Reuse of industrial wastewater ★ RO pretreatment Detailed Photos   Plant photo Packaging & ShippingCustomer site Certification and test report FAQ---Replace the filter cartridge step1. Receive the production instruction to replace the cartridge and confirm that the system has stopped running.2. Prepare the appropriate filter element (specification, material, size, O-ring material, type, etc.), disassembly tools, collection bucket, rags, etc.; and3. Thoroughly clean the filter housing, empty around the filter, and leave the operation area. Take protective gears with you.4. Disconnect the filter to be replaced from the system. Slowly open the exhaust port at the top of the filter and depressurise it, paying attention to safety in the process to prevent material or liquid from splashing.5. Empty the material in the filter, open the filter cover with a tool, take out the filter cartridge, and pack the cartridge in a plastic bag to be scrapped; 6 Use clean tools and rags to clean the filter.6. Use clean tools and rags to clean the inside of the filter and install the new cartridge.7. Open the plastic bag at the open end of the filter element and check whether the O-ring is intact and in place.8. Install the inflow of materials according to the method of inflow from the outside of the filter element and outflow from the inside of the filter element.9. with the appropriate wetting agent (such as water) wet O-ring and cartridge seat jack, hand-hold the cartridge near the end of the O-ring, vertically insert the cartridge cartridge socket completely into the cartridge seat jack, the cartridge inserted, remove the cartridge bag, and then install the metal cover, with tools to tighten the filter; 10 close the filter drain port, open the plastic bag, open the filter, the filter is complete, in place.10. Close the liquid discharge port of the filter, open the bleeder valve at the top of the housing, slightly open the inlet valve, so that the material enters the housing until the liquid overflows from the bleeder valve at the top of the housing, at this time close the bleeder valve. Pay attention to check the disassembly place, whether there is leakage;.11. Slowly open the filter outlet valve until it is completely open. Indicates that the replacement is complete.12. Remove the tools used for replacement and cleaning tools. Clean up the surrounding area.---Bag filter instalation step 1. First of all, it is necessary to confirm whether the accessories required for the installation of bag filter have been prepared;2. Check the O-ring seal and the O-ring groove on the bag filter in order to replace the accessories in time;3. When installing the bag filter, it is necessary to place the bag filter on the work station that needs to be filtered. After connecting the inlet and outlet flanges or pipe teeth, fix the filter, smother the exhaust port, or configure the exhaust valve, and the jacket type connects the thermal insulation heat source;4. Slowly put the metal m